Recommended Practice for Power Quality Measurements in AC Power Supply Systems

1 Overview

1.1 Scope

This recommended practice establishes the data acquisition attributes necessary to characterize power quality phenomena. It establishes the data acquisition attributes necessary to characterize the electromagnetic phenomena listed in table 2 of IEEE Std. 1159-1995. This guide includes definitions, instrumentation categories and technical requirements which are related to the type of disturbance to be recorded.

1.2 Objective

The objective of this recommended practice is to describe the technical measurement requirements for each type of disturbance defined in 24 categories of typical characteristics of power system electromagnetic phenomena found in Table 2 of IEEE Std 1159-1995 (R2001). The intent of this document is that the measurements of the same signal for any parameter defined herein can be carried out with two different instruments that will produce matching results within the specified uncertainty.

The initial publication of this document covers the category of RMS voltage variations referred to as sags (or dips) and swells. (Where ever the word “sag” is used in this document, it can be interchanged with “dip”.) Subsequent revisions will address the remaining parameters. In particular, harmonics will be addressed in a manner similar to IEC 61000-4-7 Testing and Measurement Techniques on Harmonics and Interharmonics Measurements and Instrumentation, for Power Supply Systems and Equipment Connected. Transients (surges) will include the works of IEC, UIE, and other references included in the Bibliography.

2 Definitions

2.1 Background

Some definitions given in this section have not been fully harmonized with definitions made in other IEEE standards and IEC documents. Where several definitions for the same terms exist, they are both included. Before scheduling the power quality measurement, the user must select the instrument which meets their needs. This section addresses the language and the assessment specification which needs to be understood to communicate with the instrumentation supplier . Also, the user should define their needs clearly. []Without the assessment specification of the instrument, or with an inappropriate specification, users are unable to assess the severity level of the disturbance on equipment; this can lead to incorrect conclusions and costly decisions. Users should ask suppliers for the complete measurement-instrument specification, which may include the following information:

· sampling rate,

· bandwidth amplitude/frequency

· accuracy []

· precision (

· resolution (signal-to-noise ratio or effective bits)

· differential mode argument and amplitude accuracy,

· common mode rejection

· anti-aliasing filter (cut-off frequency, filter order, filter type)

· window width, (interval of the sampled signal used for each analysis)

· number of windows analysed per second,

· type of weighted window used (rectangular, triangular, Blackman, Vincent, …)

· waveform synchronization device used (electronic phase locked loop or digital synchronization),

· accuracy of the synchronized device,

· global time synchronization method used and its accuracy

· the common mode rejection ratio,

· flag when the phase locked loop is not synchronized

· flag when hardware or software error occurs,

· flag when some frequency components present in the signal are not recorded,

· immunity of the instrument to disturbances in the supply voltage (transient, voltage sag (dip)s, voltage distortion etc…),

· operating environment (temperature, vibration, humidity)

2.2 IEEE & IEC Definitions

Term	Definition	Source
Accuracy	The quantity of freedom from mistake or error which the IEC dictionary and IEEE 100 characterize as the closeness of an indicated value of a measuring instrument to the corresponding true value.	IEC dictionary and IEEE 100
	Accuracy is the degree of agreement between measured values and the true values (i.e. closeness to the reality).
Aliasing	The distortion caused by sampling a signal at an inappropriate rate and which results in the overlapping of the sidebands around the harmonics of the sampling frequency in the spectrum of the sample signal. Note.: A high frequency which exceeds the operating range of the instrument affects the frequency component in the frequency range of the analysis. IEC has requested use of an anti-aliasing filter which should attenuate to below 50 dB all frequencies above the operating range of the instrument. Observation windows may be flagged during the presence of frequency components which exceed the operating range of the instrument. If these high frequency components occur too often, the user may need a wider bandwidth instrument.	IEC dictionary
Analogsignal	A signal in which the characteristic quantity representing information may, at any instant, assume any value within a continuous interval. Note. For example, an analog signal may follow continuously the values of another physical quantity representing information	IEC dictionary
Anti-aliasing	Correction intended to reduce the aliasing.	IEC dictionary
Bandwidth	The frequency range over which a given characteristic of a channel does not differ from a reference value by more than a specified amount or ratio. Note: the given characteristic may, for example, be the amplitude/frequency, the phase/frequency or the delay/frequency characteristic. The quantitative difference between the limiting frequencies of a frequency band. For most power quality users should specify the bandwidth as the frequency for which the maximum sinusoidal input signal has decreased below the accuracy specified
Channel	Inividual measurement path through an instrument Note: “Channel” and “phase” are not the same. A voltage channel is by definition the difference in potential between two conductors. Phase refers to a single conductor. A channel may be between two phases on a poly-phase system, or between a phase and neutral, or between a phase and earth.	IEC 61000-4-30 Definition 3.1
declared input voltage, U_din	value obtained from the declared supply voltage by a transducer ratio	IEC 61000-4-30 Definition 3.2
declared supply voltage	value of a voltage different from the nominal voltage obtained by agreement between the electricity supplier and a consumer	IEC 61000-4-30 Definition 3.3
dip	See Sag.
Dynamic accuracy	Accuracy determined for a time-varying output	IEEE 100
Dynamic range	The ratio, usually expressed in decibels, of the maximum to the minimum signal input amplitude over which an amplifier can operate within some specified range of performance.	IEEE 100
flagged data	for any measurement time interval in which interruptions, sag (dip)s or swells occur, the measurement results of all other parameters made during this time interval are flagged	IEC 61000-4-30 Definition 3.5
flicker	impression of unsteadiness of visual sensation induced by a light stimulus whose luminance or spectral distribution fluctuates with time	(IEV 161-08-13) IEC 61000-4-30 Definition 3.6
Frequency bins	The inherent frequency resolution of the discrete Fourier transform function
fundamental component	component whose frequency is the fundamental frequency	(IEV 101-14-49 modified) IEC 61000-4-30 Definition 3.7
fundamental frequency	frequency in the spectrum obtained from a Fourier transform of a time function, to which all the frequencies of the spectrum are referred NOTE - In case of any remaining risk of ambiguity, the power supply frequency should be referred to the polarity and speed of rotation of the synchronous generator(s) feeding the system.	(IEV 101-14-50 modified) IEC 61000-4-30 Definition 3.8
harmonic component	any of the components having a harmonic frequency NOTE Its value is normally expressed as an r.m.s. value. For brevity, such component may be referred to simply as a harmonic	IEC 61000-2-2, definition 3.2.4.
harmonic frequency	frequency which is an integer multiple of the fundamental frequency NOTE - The ratio of the harmonic frequency to the fundamental frequency is the harmonic order	IEC 61000‑2-2, definition 3.2.3
hysteresis	phenomenon represented by a characteristic curve which has a branch, called ascending branch, for increasing values of the input variable, and a different branch, called descending branch, for decreasing values of the input variable. NOTE – Sometimes a dead band effect can be superposed on a hysteresis phenomenon.	(IEV 351-14-22) IEC 61000-4-30 Definition 3.11
influence quantity	any quantity which may affect the working performance of a measuring equipment NOTE - this quantity is generally external to the measurement equipment	(IEV 311-06-01 modified). IEC 61000-4-30 Definition 3.12
interharmonic component	component having an interharmonic frequency NOTE - Its value is normally expressed as an r.m.s. value. For brevity, such a component may be referred to simply as an interharmonic	IEC 61000-2-2, definition 3.2.6
interharmonic frequency	any frequency which is not an integer multiple of the fundamental frequency NOTE 1 By extension from harmonic order, the interharmonic order is the ratio of an interharmonic frequency to the fundamental frequency. This ratio is not an integer (Recommended notation m). NOTE 2 In the case where m < 1 the term subharmonic frequency may be used.	IEC 61000-2-2, definition 3.2.5
interruption	reduction of the voltage at a point in the electrical system below a threshold	IEC 61000-4-30 Definition 3.15
interruption threshold	voltage magnitude specified for the purpose of detecting the start and the end of a voltage interruption	IEC 61000-4-30 Definition 3.16
Maximum swell magnitude voltage	The largest value of U_rms(1/2)measured on any channel during the swell.	IEC 61000-4-30 Definition 5.4.3.2
Mean ():	where N is total number of samples, x_i is the i^thsample
measurement uncertainty	maximum expected deviation of a measured value from its actual value	IEC 61000-4-30 Definition 3.17
Missing voltage	The voltage waveform that would need to be generated and summed into a sag or swell waveform to restore it to the original (pre-fault) waveshape.
nominal voltage, U_N	voltage by which a system is designated or identified	IEC 61000-4-30 Definition 3.18
overdeviation	difference between the measured value and the nominal value of a parameter, only when the measured value of the parameter is greater than the nominal value	IEC 61000-4-30 Definition 3.19
power quality	The concept of powering and grounding sensitive equipment in a manner that is suitable to the operation of that equipment. NOTE—Within the industry, alternate definitions or interpretations of power quality have been used, reflecting different points of view. Therefore, this definition might not be exclusive, pending development of a broader consensus.	Heydt, G.T. 1991. Electric power quality. West LaFayette, Indiana: Stars in a Circle Publications.
	characteristics of the electricity at a given point on an electrical system, evaluated against a set of reference technical parameters. NOTE These parameters might, in some cases, relate to the compatibility between electricity supplied on a network and the loads connected to that network.	IEC 61000-4-30 Definition 3.20
Observation Window	Sampled signal which occurs during a predefined period.	IEC 61000-4-30
Precision	The quantity of coherence or repeatability of measurement data, customarily expressed in terms of the standard deviation of the extended set of measurement results from a well-defined (adequately specified) measurement process in a state of statistical control. The standard deviation of the conceptual population is approximated by the standard deviation of an extended set of actual measurements.
	Precision is an indication of the likelihood that a measurement will differ from the same measurement at a different, but not correlated, time. The assessment interval specification is also needed to assess precision values. For example, the precision could be assessed using measurements every 3-s interval.
Resolution	The smallest change in the measured or supplied quantity to which a numerical value can be assigned without interpolation. Note.: the resolution of most digital instruments is specified in terms of the number of bits that the analogue to digital converter can provide. Suppliers have invented several wordings such as effective bits.	IEC dictionary
r.m.s. ()	The root mean square,defined by, where N is number of measurements, x_i is the i^th measurement.
	square root of the arithmetic mean of the squares of the instantaneous values of a quantity taken over a specified time interval and a specified bandwidth	(IEV 101-14-16 modified). IEC 61000-4-30 Definition 3.21
r.m.s. voltage refreshed each half cycle, U_rms(1/2)	value of the r.m.s. voltage measured over one cycle, commencing at a fundamental zero-crossing, and refreshed each half cycle NOTE1: This technique is independent for each channel, and will produce r.m.s. values at successive times on different channels for polyphase systems. NOTE2: This value is used only for voltage sag (dip), voltage swell, and interruption detection	IEC 61000-4-30 Definition 3.22
Range of influence quantities	range of values of a single influence quantity	IEC 61000-4-30 Definition 3.23
reference channel	one of the voltage measurement channels designated as the reference channel for poly-phase measurements	IEC 61000-4-30 Definition 3.24
retained voltage, U_ret	minimum value of U_rms(1/2)recorded during a voltage sag (dip) or interruption. NOTE The retained voltage is expressed as a value in volts, or as a percentage or per unit value of the declared input voltage.	IEC 61000-4-30 Definition 3.25

sliding reference voltage, U_sr	voltage magnitude averaged over a specified time interval, representing the voltage preceding a voltage sag (dip) or swell NOTE - The sliding reference voltage is used to determine the voltage change during a sag (dip) or a swell	IEC 61000-4-30 Definition 3.26
sag (dip) threshold	voltage magnitude specified for the purpose of detecting the start and the end of a voltage sag. The use of the term dip is the equivalent of sag for purposes of this document.	IEC 61000-4-30 Definition 3.27
Sampled signal	Signal representing a variable which is only intermittently observed and represented. The sequence of values of a signal taken at discrete instants.
Sideband	The spectral components resulting from the modulation of a sinusoidal carrier and lying above or below the carrier frequency. Note: Sideband designates a frequency band lying above or below a sinusoidal carrier frequency and containing spectral components of significance produced by modulation. Flicker originated from a lamp is produced by the modulation of the power-system voltage operated at the fundamental frequency. Thus, the fundamental frequency is the carrier frequency and the modulation produces the sidebands.	IEC dictionary
signal	A measurable variable, one or more parameters of which carry information about one or more variables which the signal represents
swell threshold	voltage magnitude specified for the purpose of detecting the start and the end of a swell	IEC 61000-4-30 Definition 3.27
time aggregation	combination of several sequential values of a given parameter (each determined over identical time intervals) to provide a value for a longer time interval Note Aggregation in this document always refers to time aggregation.	IEC 61000-4-30 Definition 3.28
Traceability	Traceability is an attribute of some measurements. Measurements have traceability to the designated standards if an only if scientifically rigorous evidence is produced on a continuing basis to show that the measurement process is producing measurement results (data) for which the total measurement uncertainty, relative to national or other designated standards is quantified
underdeviation	absolute value of the difference between the measured value and the nominal value of a parameter, only when the value of the parameter is lower than the nominal value
Voltage sag (dip)	temporary reduction of the voltage at a point in the electrical system below a threshold NOTE - 1: Interruptions are a special case of sag (dip). Post-processing may be used to distinguish between sag (dip)s and interruptions. NOTE - 2; In some areas of the world a voltage sag (dip) is referred to as sag. The two terms are considered interchangeable, however this standard will only use the term voltage sag (dip).
voltage swell	temporary increase of the voltage at a point in the electrical system above a threshold
voltage unbalance	condition in a poly-phase system in which the r.m.s. values of the line voltages (fundamental component), or the phase angles between consecutive line voltages, are not all equal NOTE - 1: The degree of the inequality is usually expressed as the ratios of the negative and zero sequence components to the positive sequence component NOTE - 2: In this standard voltage unbalance is considered in relation to three-phase systems.	(VEI 161-08-09 modified) IEC 61000-4-30 Definition 3.31

2.3 Classes of measurement performance

For each parameter measured, two classes of measurement performance are defined:

· Class A performance

· This class of performance is used where precise measurements are necessary, e.g. for contractual applications, verifying compliance with standards, resolving disputes, etc. Any measurements of a parameter carried out with two different instruments complying with the requirements of class A, when measuring the same signals, will produce matching results within the specified uncertainty.

To ensure that matching results are produced, class A performance instrument requires a bandwidth characteristic and a sampling rate sufficient for the specified uncertainty of each parameter.

· Class B performance

This class of performance may be used for statistical surveys, troubleshooting applications, and other applications where low uncertainty is not required.

For each performance class the range of influencing factors that shall be complied with is specified in Section 5. Users shall select the class of measurement performance taking account of the situation of each application case.

NOTE - 1: A measurement instrument may have different performance classes for different parameters.

NOTE - 2: The instrument supplier shall declare influence quantities which are not expressly given and which may degrade performance of the instrument.

3 Organization of the measurements

3.2 Basic Blocks

The electrical quantity to be measured may be either directly accessible, as is generally the case in low-voltage supply systems, or accessible via measurement transducers.

The whole measurement chain is shown in Figure 1.

Figure 1 – Measurement chain

An "instrument" usually includes the whole measurement chain (see Figure 1). In this standard, the normative part does not consider the measurement transducers including uncertainty, but the Annex A.2 gives guidance.

3.3 Electrical values to be measured

Measurements can be performed on single-phase or poly-phase supply systems. Depending on the context, it may be necessary to measure voltages between phase conductors and neutral (line-to-neutral) or between phase conductors (line-to-line) or between neutral and earth. It is not the purpose of this standard to impose the choice of the electrical values to be measured. Moreover, except for the measurement of voltage unbalance, which is intrinsically poly-phase, the measurement methods specified in this document are such that independent results can be produced on each measurement channel.

Current measurements can be performed on each conductor of supply systems, including the neutral conductor and the protective earth conductor.

NOTE: It is often useful to measure current simultaneously with voltage, and to associate the current measurements in one conductor with voltage measurements between that conductor and a reference conductor, such as an earth conductor or a neutral conductor.

3.4 Measurement aggregation over time intervals

· For class A performance

A measurement time interval of magnitudes (supply voltage, harmonics, interharmonics and unbalance) shall be over a 10-cycle time interval for 50 Hz power system or 12-cycle time interval for 60 Hz power system.

NOTE The uncertainty of this measurement is included in the uncertainty measurement protocol of each parameter.

Measurement time intervals are aggregated over three different time intervals. The aggregation time intervals are:

– 3-s interval (150 cycles for 50 Hz nominal or 180 cycles for 60 Hz nominal),

– 10-min interval,

– 2-h interval.

· For class B performance

The supplier shall indicate the method, number and duration of aggregation time intervals.

3.4.1 Measurement aggregation algorithm

Aggregations are performed using the square root of the arithmetic mean of the squared input values.

NOTE: For flicker measurements, the aggregation algorithm is different (see IEC 61000‑4-15).

Three categories of aggregation are necessary:

– Cycle aggregation

The data for the 150/180-cycle time interval shall be aggregated from fifteen 10/12-cycle time intervals.

NOTE: This time interval is not a "time clock" interval; it is based on the frequency characteristic.

– From cycle to time clock aggregation

The 10-minute value shall be tagged with the absolute time (e.g. 01H10.00). The time tag is that at the end of the 10-minute aggregation. If the last 10/12 cycle value in a 10-minute aggregation period overlaps in time with the absolute 10-minute clock boundary, that 10/12 cycle value is included in the aggregation for this 10-minute interval.

On commencement of the measurement, the 10/12 cycle measurement shall be started at the boundary of the absolute 10-minute clock, and shall be re-synchronised at every subsequent 10-minute boundary.

Note: This technique implies that a very small amount of data may overlap and appear in two adjacent 10-minute aggregations.

– Time clock aggregation

The data for the “2-h interval” shall be aggregated from twelve 10-min intervals.

3.4.2 Time clock uncertainty

The time clock uncertainty is:

· For class A performance

± 20 ms for 50 Hz or ± 16,7 ms for 60 Hz.

NOTE - 1: This performance can be achieved, for example, through a synchronization procedure applied periodically during a measurement campaign, or through a GPS receiver, or through reception of transmitted radio timing signals. The recalibration rate should be at a rate necessary to maintain the required time accuracy.

NOTE - 2: When synchronisation by an external signal becomes unavailable, the time tagging tolerance must be better than 1 seconds /24 hours.

NOTE - 3: This performance is necessary to ensure that two class A instruments produce the same 10-min aggregation results when connected to the same signal.

NOTE 4: When a threshold is crossed, it may be useful to record the date and time.

· For class B performance

The supplier shall specify the method to determine 10-min intervals.

4 Supply voltage sag (dip)s and swells

4.2 Basic measurement

The basic measurement of a voltage sag (dip) and swell shall be the U_rms(1/2) on each measurement channel.

NOTE - 1: For class A, the cycle duration for U_rms(1/2) depends on the frequency. The frequency might be determined by the last non-flagged power frequency measurement, or by any other method that yields the uncertainty requirements of Section 5.

NOTE - 2: The U_rms(1/2)value includes, by definition, harmonics, interharmonics, ripple control signals, etc.

4.2.1 Detection and evaluation of a voltage sag (dip)

4.2.1.1 Voltage sag (dip) detection

The sag (dip) threshold is a percentage of either U_din or the sliding voltage reference U_sr(see 5.4.4). The user shall declare the reference voltage in use.

NOTE: Sliding voltage reference U_sr is generally not used in LV systems. See IEC 61000-2-8 for further information and advice.

– On single-phase system, a voltage sag (dip) begins when

– the U_rms(1/2)voltage falls below the sag (dip) threshold, and ends when the U_rms(1/2)voltage is equal to or above the sag (dip) threshold plus the hysteresis voltage. This method is only resolvable to +/- ½ cycle, or,

– When the DC equivalent voltage drops (see Section 6.9) below a threshold and ends when the DC equivalent voltage is equal to or above the threshold plus the hysteresis voltage.

– On polyphase system a sag (dip) begins

o when the U_rms(1/2)voltage of one channel, at least, is below the sag (dip) threshold and ends when the U_rms(1/2)voltage on all measured channels is equal to or above the sag (dip) threshold plus the hysteresis voltage. This method is only resolvable to +/- ½ cycle.

o When the DC equivalent voltage drops below a threshold and ends when the DC equivalent voltage is equal to or above the threshold plus the hysteresis voltage.

– The sag (dip) threshold and the hysteresis voltage are both set by the user according to the use.

4.2.1.2 Voltage sag (dip) evaluation

A voltage sag (dip) is characterized by a pair of data, either retained voltage (u_ret) or depth and duration.

– The retained voltage is the smallest U_rms(1/2) value measured on any channel during the sag (dip).

– The depth is the difference between the reference voltage (either U_din or U_sr) and the retained voltage. It is generally expressed in % of the reference voltage.

– The duration of a voltage sag (dip) is the time difference between the beginning and the end of the voltage sag (dip).

– Missing voltage (see Annex 6.5) can provide a different precision on the beginning and ending on the DC equivalent voltage to what:

– an ASD experiences for over/undervoltage measurements.

– Contactors respond to. [RANDY]

– Sliding window can provide an interpretative beginning and ending on the DC equivalent voltage for utility benchmark methods.

NOTE - 1: The sag (dip) duration measurement can be started on one channel and terminated on a different channel.

NOTE - 2: Voltage sag (dip) envelopes are not necessarily rectangular. As a consequence, for a given voltage sag (dip), the measured duration is dependent on the selected sag (dip) threshold value. The shape of the envelope may be assessed using several sag (dip) thresholds set within the range of voltage sag (dip) and voltage interruption thresholds detection.

NOTE - 3: Typically, the hysteresis is equal to 1 to 2 % of U_din.

NOTE - 4: Sag (dip) thresholds are typically90 % of the voltage reference

NOTE - 5: Retained voltage is often useful to end-users, and may be preferred because it is referenced to zero volts. In contrast, depth is often useful to electric suppliers, especially on HV systems or in cases when a sliding reference voltage is used.

NOTE - 6: Phase shift may occur during voltage sag (dip)s. See Section 6.4.

NOTE - 7: When a threshold is crossed, it may be useful to record the date and time.

4.2.2 Detection and evaluation of a voltage swell

4.2.2.1 Voltage swell detection

The swell detection threshold is a percentage of either U_din. or the sliding voltage reference U_sr(see 5.4.4). The user shall declare the reference voltage in use.

NOTE Sliding voltage reference U_sr is generally not used in LV systems. See 61000-2-8 for further information and advice.

– On single-phase system a swell begins when the U_rms(1/2) voltage is above the swell threshold, and ends when the U_rms(1/2) voltage is equal to or below the swell threshold minus the hysteresis voltage.

– On poly-phase system a swell begins when the U_rms(1/2) voltage of one channel, at least, is above the swell threshold and ends when the U_rms(1/2) voltage on all measured channels is equal to or below the swell threshold minus the hysteresis voltage.

– DC Equivalent wording supplemented by R,A,E.

The swell threshold and the hysteresis voltage are both set by the user according to the use.

4.2.2.2 Voltage swell evaluation

A voltage swell is characterised by a pair of data, maximum swell voltage magnitude and duration.

– The maximum swell magnitude voltage is the largest U_rms(1/2) value measured on any channel during the swell.

– The duration of a voltage swell is the time difference between the beginning and the end of the swell.

NOTE - 1: The swell duration measurement can be started on one channel and terminated on a different channel.

NOTE - 2: Swell envelopes may not be rectangular. As a consequence, for a given swell, the measured duration is dependent on the swell threshold value.

NOTE - 3 Typically, the hysteresis is equal to 1- to 2 % of U_din.

NOTE - 4: the swell threshold is typically greater than 105 to 110 % of U_din

NOTE - 5: Phase shift may also occur during voltage swells.

NOTE - 6: When a threshold is crossed, it may be useful to record the date and time.

4.2.3 Calculation of a sliding reference voltage

If a sliding reference is chosen for voltage sag (dip) or swell detection, this shall be calculated using a first-order filter with a 1-min time constant. This filter is given by:

U_sr(n) = 0.9967 x U_sr(n–1) + 0.0033 x U_(10/12)rms

where

U_sr(n)is the present value of the sliding reference voltage,

U_sr(n–1)is the previous value of the sliding reference voltage, and

U_(10/12)rmsis the most recent 10/12-cycle r.m.s. value.

When the measurement is started, the initial value of the sliding reference voltage is set to the declared input voltage. The sliding reference voltage is updated every 10/12-cycles. If a 10/12-cycle value is flagged, the sliding reference voltage is not updated and the previous value is used.

4.2.4 Measurement uncertainty

4.2.4.1 Retained voltage and maximum swell voltage magnitude measurement uncertainty

· For class A performance

The uncertainty shall be DU = ±0.2 % of U_din.

· For class B performance

The supplier shall specify the uncertainty. In all cases the uncertainty DU shall be ±1.0 % of U_din.

4.2.5 Duration measurement uncertainty

· For class A and class B performances

The uncertainty of a sag (dip) or swell duration is equal to the sag (dip) or swell commencement uncertainty (half a cycle) plus the sag (dip) or swell conclusion uncertainty (half a cycle).

Range of influence quantities and implementation verification

4.1 Range of influence quantities

The measurement of a specific characteristic can be adversely affected by the application of a disturbing influence (influence quantity) on the electrical input signal; e.g. the measurement of supply voltage unbalance can be adversely affected if the voltage waveform is at the same time subject to a harmonic disturbance.

The result of a parameter measurement shall be within the specified uncertainty given in this section when all other parameters are within their range of variation, given in the Tables 5-1 and 5-2.

Table 5-1 – Range of influence quantities (of the input signals) for class A performance

Influence quantities	Range of variation
Frequency	42,5 Hz – 57,5 Hz for 50 Hz systems 51 Hz – 69 Hz for 60 Hz systems
Voltage magnitude (steady state)	0 % – 200 % of U_din
Flicker (P_st)	0 – 20
Unbalance	0 % – 5 %
Harmonics (THD)	Twice the values in IEC 61000‑2-4, class 3, which are listed in Table 5-1a
Interharmonics (at any frequency)	Twice the values in IEC 61000‑2-4, class 3, which are only those interharmonic frequencies below the 2^nd harmonic that would result in a flicker severity Pst = 1.
Mains signalling voltage	0 – 9 % of U_din

NOTE: Pst shall be produced by periodic modulation.

per 61000-2-4: Table 5
Total Harmonic Distortion	10%

per 61000-2-4: Table 3 Odd harmonics, multiples of 3	Class 3 Uh (%)	per 61000-2-4: Table 2 Odd harmonics, non multiples of 3	Class 3 Uh (%)	per 61000-2-4: Table 4 Even harmonics	Class 3 Uh (%)
3	6	5	8	2	3
9	2.5	7	7	4	1.5
15	2	11	5	6	1
21	1.75	13	4.5	8	1

Charles Perry, Chair

Richard Bingham
Math Bollen	Scott Peele
Randy Collins	Dan Sabin
Andrew Dettloff	Georges Simard
Erich Gunther	Timothy Unruh
Mark Kempker	David Vannoy
Christopher Melhorn	Marek Waclawiak
R. Larry Morgan	James Wikston
Alex McEachern

1.2 Objective

Term

Accuracy

4.2.1.1 Voltage sag (dip) detection

4.2.1.2 Voltage sag (dip) evaluation

4.2.2.1 Voltage swell detection

4.2.2.2 Voltage swell evaluation

4.2.4 Measurement uncertainty

4.2.4.1 Retained voltage and maximum swell voltage magnitude measurement uncertainty

4.1 Range of influence quantities