Thread Links Date Links
Thread Prev Thread Next Thread Index Date Prev Date Next Date Index

Re: [8023-10GEPON] Question about dual MII solution



Dear Brian, 
That seems fine with a small restriction tough - what about the 1G systems which operate with the tight power budget and the loss of 1-2 dB of effective sensitivity may result in the loss of link integrity. I think such an option was already brought up on the reflector and the main concern was exactly for the backward compatibility with the tight budget 1 G systems.
Best wishes
Marek

________________________________

De: Brian Holden [mailto:Brian_Holden@pmc-sierra.com]
Enviada: ter 1/16/2007 7:42
Para: Hajduczenia, Marek; STDS-802-3-10GEPON@listserv.ieee.org
Assunto: RE: [8023-10GEPON] Question about dual MII solution


Marek,
My guess (and only a guess) is that a dual-rate TIA could be designed that was optimized for 10G and which is sub-optimal by one or two dBs in 1G operation.
  Thanks, Brian H.
 

_______________________________________________ 
Brian Holden        PMC-Sierra, Inc. 
3975 Freedom Circle, Santa Clara  CA  USA 
+1.408.239.8123   Fax +1.408.492.9462  
brian_holden@pmc-sierra.com   http://www.pmc-sierra.com <http://www.pmc-sierra.com/>     

	-----Original Message-----
	From: Hajduczenia, Marek [mailto:marek.hajduczenia@siemens.com]
	Sent: Tuesday, January 16, 2007 6:41 AM
	To: Brian Holden; STDS-802-3-10GEPON@listserv.ieee.org
	Subject: RE: [8023-10GEPON] Question about dual MII solution
	
	
	Dear Brian, 
	the real question is whether the solution 2a is viable without the need to go into two discrete TIAs and having to switch between them in the anticipation of the incoming burst, since then the same problem as in point 1 arises I believe. You would have to switch off one of the TIAs in advance. Additionally, there is a problem of reduced signal amplitude versus noise background that Frank was addressed if the electrical signal needs to be separated into two paths before TIA.
	I do not know whether anybody in our group has sufficient expertise in the design of TIAs to state clearly that such dual data rate TIA design is feasible at first and can be cost effective as a second requirement. What do You think about it ?
	 
	Best wishes
	Marek

________________________________

	De: Brian Holden [mailto:Brian_Holden@PMC-SIERRA.COM]
	Enviada: seg 1/15/2007 7:27
	Para: STDS-802-3-10GEPON@listserv.ieee.org
	Assunto: [8023-10GEPON] Question about dual MII solution
	
	

	All,
	During the break, I was suggesting the following to several folks:
	
	Question - Is the assertion that Frank E. made that the initial Trans-Impedance Amplifier needs to know what rate is coming to be configured properly true?
	
	   1)  if true, then one possible solution may be to
	        a) set up a schedule for the receiver via the XGMII management interface (the encoding may need to be clever to fit into the unused registers)
	            b) the latency properties of that management interface may need to be constrained to allow the schedule setup in real-time
	
	   2) if false, then the dual MII solution is likely workable
	            a)  presumably the solution would involve some sort of "dual Trans-Impedance Amplifier"
	            b)  a likely compromise is that some additional loss over what would be needed for bandwidth optimized designs may need to be budgeted for
	
	  Brian Holden
	  PMC-Sierra
	
	_______________________________________________
	Brian Holden        PMC-Sierra, Inc.
	3975 Freedom Circle, Santa Clara  CA  USA
	+1.408.239.8123   Fax +1.408.492.9462 
	brian_holden@pmc-sierra.com   http://www.pmc-sierra.com