Thread Links Date Links
Thread Prev Thread Next Thread Index Date Prev Date Next Date Index

Re: XAUI IO specs




Mike,

On your P.S., I was referencing slide 13 from the proposal authored by Mr. Ali
Ghiasi and Mr. Richard Dugan presented at the November '99 HSSG meeting in
Kauai, HI:
http://grouper.ieee.org/groups/802/3/10G_study/public/nov99/ghiasi_1_1199.pdf
The legends on the Y-axis come from the table on slide 5. Note the reference to
0V, or ground on slide 13. 

Best Regards,
Rich
 
--

Mike Jenkins wrote:
> 
> ps:  On rereading Rich's note, if by "positive differential signal"
>     he meant the difference of two signals, then his description
>     is the same as mine (but then "referenced to ground" is
>     confusing, because only single-ended signals are referenced
>     to anything -- dif'l signals are referenced to each other).
>     This is the type of confusion that haunts anyone specifying
>     dif'l signals unless everyone is brutally unambiguous.
> 
> Rich Taborek wrote:
> >
> > Mark,
> >
> > I'll have to defer to Mr. Ali Ghiasi and Mr. Richard Dugan on this issue to
> > properly resolve the nomenclature. My understanding of the parameters listed is
> > as follows using Vo Dif(max) 800 mV as an example:
> >
> > When the Output is set to a logic one, the positive differential signal,
> > referenced to a 0 V ground, is a maximum of +400 mV and the negtive differential
> > signal, referenced to a 0 V ground, is a maximum of -400 mV.
> >
> > When the Output is set to a logic zero, the positive differential signal,
> > referenced to a 0 V ground, is a maximum of -400 mV and the negtive differential
> > signal, referenced to a 0 V ground, is a maximum of +400 mV.
> >
> > I'd call this V diff peak-to-peak, but this I'm NOT an expert in this area.
> >
> > Best Regards,
> > Rich
> >
> > --
> >
> > Mark Kerestes wrote:
> > >
> > > Rich, Ali
> > >  On slide 22 of the XAUI/XGXS Proposal from Albuquerque was listed :
> > > Vo Dif(max) 800mV
> > > Vo Dif(min) 500mV
> > > Vin Dif(max)  1000mV
> > > Vin Dif(min) 175mV
> > > I assume these are truely Vdif and NOT Vdif peak to peak? I have some
> > > confusion from looking back at the
> > > Nov 5 1999 "HARI the Electrical Interface" which seems to have a table
> > > that mixes Vdif and Vdif peak to peak
> > > showing PECL vs LVDS vs HARI side by side.
> > > Best regards,
> > > Mark

> ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
>  Mike Jenkins               Phone: 408.433.7901            _____
>  LSI Logic Corp, ms/G715      Fax: 408.433.7461        LSI|LOGIC| (R)
>  1525 McCarthy Blvd.       mailto:Jenkins@xxxxxxxx        |     |
>  Milpitas, CA  95035         http://www.lsilogic.com      |_____|
> ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
                                     
------------------------------------------------------- 
Richard Taborek Sr.                 Phone: 408-845-6102       
Chief Technology Officer             Cell: 408-832-3957
nSerial Corporation                   Fax: 408-845-6114
2500-5 Augustine Dr.        mailto:rtaborek@xxxxxxxxxxx
Santa Clara, CA 95054            http://www.nSerial.com