Thread Links Date Links
Thread Prev Thread Next Thread Index Date Prev Date Next Date Index

Re: Equalization




Vipul:

It is a good summary.  They are all true.

However, we know all these facts for quite a while, and they are not new to 
us.
They are not simple problems to be resolved overnight.  It will take 
systematic approach and time to solve.  I do not expect a miracle in 
September to come out all answers -- rush, rush does not produce miracle.

Be practical, solid and smart to approach any problem.

What I do not understand is why some people have to limit to 3 PMD only.  
There is no justified reason at all to insist 3-PMDs; as a result, the 3-PMD 
is forcing us to produce a miracle.  GIVE US A BREAK !!  A successful project 
is always completed by practical approaches, but not by a miracle.

We can vote 5 PMDs in, then we can concentrate next whole year to resolve all 
those issues -- this is practical, and doable.


Regards, 

Ed Chang
NetWorth Technologies, Inc  

  
 Dear colleagues,
 
 Okay, so where are we? Let me review what I think I have heard so
 far.
 
 Yes, the idea of 10G Serial on installed MMF is interesting, but
 there are a couple of holes in the proposal, including bad timing.
 Here is the summary, followed by holes.
 
 850 nm Serial solution:
 -----------------------
 - Will benefit from TIA FO 2.2 Encircled Flux and Restricted Mode
 Launch work.
 - Offset Launch jumper not required.
 - Start with 385 MHz-Km bandwidth assumption on installed MMF.
 - Add 6 dB equalization to support 100 meters operation, additional
 9.54 dB to support 300 meters. Equalization has to be adaptive, in
 the sense that impulse response will be different for each link. It
 must overcome severe DMD in some cases. With Encircled Flux launch,
 for a given link, the impulse response will not vary significantly
 with time, so it can be assumed as time-invariant or very slowly
 varying in time.
 - Potentially, end up with a total of 3 PMDs that meet all 5
 Objectives.
 
 1310 nm Serial solution:
 -----------------------
 - Will benefit from EMB work done with 802.3z.
 - Offset Launch jumper is required.
 - Start with 500 MHz-Km bandwidth assumption on installed MMF.
 - Add 4 dB equalization to support 100 meters operation, additional
 9.54 dB to support 300 meters. Equalization has to be adaptive in
 the sense that impulse response will be different for each link. It
 must overcome severe DMD in some cases. With offset launch, for a
 given link, the impulse response will not vary significantly with
 time, so it can be assumed as time-invariant or very slowly varying
 in time.
 - Potentially, end up with a total of 2 PMDs that meet all 5
 Objectives.
 
 List of holes:
 -------------
 
 1. It hasn't been established that Encircled Flux over a randomly
 selected fiber from installed base will ensure 385 MHz-Km bandwidth
 (850 nm) with a high degree of statistical confidence. Gair's
 suggestion of tagging an RML-compliance condition is one possible
 solution. We need to know if that suggestion will be acceptable to
 802.3ae end users and system integrators.
 
 2. It hasn't been established that 10G equalization is feasible. By
 feasible, I mean something like - a demonstrable solution before the
 Working Group Ballot, capable of overcoming severe DMD, consuming
 less than 3 watts, with a cost comparable to that of other
 components, backed by technical presentations in September that
 instill a high degree of confidence in the 802.3ae members.
 
 3. Perhaps it is too late. There is a high likelihood that at the
 September Interim, motions to adopt other PMDs that meet Objectives
 1 and 2 will pass.
 
 Hole 1 can be bypassed by adopting a 1310 nm Serial solution. Hole 2
 can't be plugged until we have heard presentations from DSP experts
 in September. Hole 3 is the most regrettable. I don't know how to
 plug it. Jonathan, Walt, do you have any comments or suggestions?
 
 Thanks,
 Vipul >>