Thread Links Date Links
Thread Prev Thread Next Thread Index Date Prev Date Next Date Index

RE: Clause 49 /A/ /K/ /R/ on XGMII question




I agree with you that this is the appropriate starting point, but one of the
subtle problems with "The RS shall treat any control character received
after a Start control character other than a Terminate control character as
an error, see 46.3.3.1." is that it ignores alignment of the Start, and the
lower case "error" to some may not imply "Error control character".

--Bob Grow

-----Original Message-----
From: pat_thaler@xxxxxxxxxxx [mailto:pat_thaler@xxxxxxxxxxx]
Sent: Thursday, February 15, 2001 12:49 PM
To: bob.grow@xxxxxxxxx; pat_thaler@xxxxxxxxxxx;
jgaither@xxxxxxxxxxxxxxx; stds-802-3-hssg@xxxxxxxx
Subject: RE: Clause 49 /A/ /K/ /R/ on XGMII question



Bob,

The clause already contains the following: "The RS shall treat any control
character received after a Start control character other than a Terminate
control character as an error, see 46.3.3.1." (p261 l52). 46.3.3.1 could use
some work to better match it to that, but it is a start.

Pat

-----Original Message-----
From: Grow, Bob [mailto:bob.grow@xxxxxxxxx]
Sent: Wednesday, February 14, 2001 4:18 PM
To: 'pat_thaler@xxxxxxxxxxx'; jgaither@xxxxxxxxxxxxxxx;
stds-802-3-hssg@xxxxxxxx
Subject: RE: Clause 49 /A/ /K/ /R/ on XGMII question



I have some comments to submit on clause 46 to clarify the XGMII control
characters that should be treated in the same way as Error control
characters.  I plan to recommend that all received control characters except
Terminate (including the reserved control characters like unfiltered /A/,
/K/, /R/) in a frame be treated as Error control characters.  That
eliminates the need for a redundant filtering function in the PCS.  The
related part of the comments is to better define delimitation of a received
frame by improving the specification of DATA_VALID_STATUS being set to
DATA_NOT_VALID.  

All of this is consistent with what Pat says below.

--Bob Grow

-----Original Message-----
From: pat_thaler@xxxxxxxxxxx [mailto:pat_thaler@xxxxxxxxxxx]
Sent: Wednesday, February 14, 2001 2:52 PM
To: jgaither@xxxxxxxxxxxxxxx; stds-802-3-hssg@xxxxxxxx
Subject: RE: Clause 49 /A/ /K/ /R/ on XGMII question



Justin,

The XGXS only converts /A/, /K/, and /R/ to /I/ when they occur in a whole
column: an ||A||, ||K||, or ||R|| ordered set. Therefore, one type of error
that would cause /A/, /K/, or /R/ on the XGMII output from an XGXS would be
a bit error that changed the value of one or more bytes in an ordered set.
If such an error happens, there is no particular reason for a 10GBASE-R PCS
to change the remaining /A/, /K/ and /R/ symbols to an /E/. We have code
table entries for them and replacing them with something else would
complicate implementation.

The primary purposes of sending an /E/ are: 
  to avoid changing an unencodeable input into something that might produce
an undetectable error. 
  to propogate special error detection that preserves delimiter Hamming
distance so that code dependent 0- to 3-bit errors don't produce
undetectable errors.

Neither of those purposes would be served by changing a spurious /A/, /K/ or
/R/ into an /E/. Furthermore, the RS has to handle receiving these /A/, /K/
and /R/ code groups because an XGXS might be directly connected to the RS.
If one believes that /A/, /K/ and /R/ should not be allowed to exist at the
XGMII interface, than it is the 10GBASE-X/XGXS coding rules that should be
changed and not 10GBASE-R.

Regards,
Pat 

-----Original Message-----
From: Justin Gaither [mailto:jgaither@xxxxxxxxxxxxxxx]
Sent: Wednesday, February 14, 2001 11:29 AM
To: 802.3ae
Subject: Clause 49 /A/ /K/ /R/ on XGMII question


Hello,
	Page 345 line 30-31 says "The codes for /A/ /K/ and /R/ are used on
the
XAUI interface to signal idle.  They are not present on the XGMII when
no errorrs have occurred, but certain bit errors cause the XGXS to send
them on the XGMII."

What types of errors would this be? and why would we want allow them to
continue through the 10GBase-R, into the optional WIS and onto the link?

Should these be replaced by /E/?


-- 
Justin Gaither                       Phone: 512-306-7292  x529
RocketChips a Division of Xilinx     Fax:   512-306-7293
500 N. Capital of TX Hwy.
Bldg 3                         email: jgaither@xxxxxxxxxxxxxxx
Austin, TX 78746               WWW:   www.rocketchips.com