Thread Links Date Links
Thread Prev Thread Next Thread Index Date Prev Date Next Date Index

Re: [802.3ae] D3.1 Clause 45 and Clause 48 potential inconsistencies




Boaz,

48.2.5.4.1, Link status detection, is general about local_fault
conditions. It ends with: "A local_fault condition may also be
recognized by any 10GBASE-X process upon detection of an error condition
which prevents continued reliable operation, but that is beyond the
scope of
this standard." This definition is applicable to the 10GBASE-X PCS as
well as both the DTE and PHY XGXS.

It follows that the condition for setting management register bit 5.8.10
includes "any error condition which prevents continued reliable
operation" where that error condition is detected or recognized by the
DTE XGXS only. Included in the preceding set of error conditions is the
specific error condition that you note: "Has not synchronized and
aligned all four receive lanes".

I believe that we're on track (1.b) per your note and that the wording
in 48.2.5.4.1 is complete.

In response to your track (2) inquiry, 48.2.5.4.1 points out that the
definition of such conditions are beyond the scope of the standard. To
give you an idea of the possible conditions, one is that a PMA reference
clock input may be non-operational, assuming one is required.

Best Regards,
Rich
                 
--

Boaz Shahar wrote:
> 
> Ben,
> I understand your position about commenting. However, before commenting, I
> think I should try to understand the intention there. I'll try to put my
> question in a more direct way here, and may will submit another discussion
> about the DTE-XS vs. the PHY-XS status definition bits later. So here are
> the questions regarding the DTE-XS initially:
> 
> Questions
> (1) What is the condition for setting bit 5.8.10 ? (p.234) Or: What is the
> definition of the event: "The DTE has detected a LF condition on the Receive
> path"? Is this the same as: "Has not synchronized and aligned all four
> receive lanes"?
> AND:
> (1.a) If the answer to (1) is "Yes", Do we need the duplication of the same
> function on 3 bits: 5.1.2, 5.8.10, and 5.24.12?
> (1.b) If the answer to (1) is "No", then what is the exact definition and
> how the sentence "A local Fault condition is recognized by the PCS Rx
> process whenever align_status=fail" (Clause 48 P. 307) can be explained?
> 
> (2) What is the condition for setting 5.8.11 (P.233): Is that user defined?
> If not what is the definition of the event: "..the DTE-XS Has detected an LF
> condition on the Tx path"
> 
> Thx. for your help,
> Boaz
> 
> > -----Original Message-----
> > From: Ben Brown [mailto:bbrown@xxxxxxxx]
> > Sent: Friday, July 20, 2001 1:08 AM
> > To: Boaz Shahar
> > Cc: HSSG (E-mail)
> > Subject: Re: [802.3ae] D3.1 Clause 45 and Clause 48 potential
> > inconsistencies
> >
> >
> >
> >
> > Boaz,
> >
> > Boaz Shahar wrote:
> > >
> > > Hi there,
> > > I would like to clarify certain things regarding LF, RF and
> > Link Status:
> > >
> > > 1.Status bit 5.1.7 suppose to to be set by the transmitter
> > if it detects a
> > > LF sequence in its input OR set by the receiver if it
> > detects LF in its
> > > inputs? I think it is NOT set if the receiver detects inter
> > lane miss
> > > alignment condition (That is, it is not set by the receiver
> > if the receiver
> > > GENERATES LF as opposed to DETECTING LF). Is that so?
> >
> > I don't think so. Bit 5.1.7 says it is an "OR" function of bits
> > 5.8.11 and 5.8.10. The first sentence of the 5.8.11 definition
> > says that this bit "indicates that the DTE XS has detected a
> > local fault condition on the transmit path". Also, the RS never
> > generates the LF sequence so the DTE XS transmit path can never
> > see the LF sequence. The first sentence of the 5.8.10 definition
> > says that this bit "indicates that the DTE XS has detected a
> > local fault condition on the receive path". I don't see any
> > mapping from the local fault conditions in clause 48 to either
> > of these bits. This should probably be fixed with a comment of
> > some sort.
> >
> > >
> > > 2.The term "DETECT LF" stands for detecting LF sequence in
> > the input to a
> > > certain function? If a receiver detects miss alignment, and
> > generates LF as
> > > a result, it is not said to be LF DETECTION event?
> >
> > I disagree. A receiver that is not in sync or alignment is
> > certainly detecting a local fault. The definition for the DTE
> > XS transmitter is implementation specific. Recall that transmit
> > is in the opposite direction for the PHY XS as it is for the
> > DTE XS or the 10GBASE-X PCS.
> >
> > >
> > > 3. Status bit 5.8.11 detects LF on the transmit path of the
> > DTE-XS. That is,
> > > set by the transmitter when it detects an LF sequence in
> > its input in the
> > > DTE-XS. Bit 4.8.11 does the same for the PHY_XS. But here,
> > transmit path
> > > means that the PHY-XS XAUI Receiver has to set this bit.
> > So, according to
> > > the current definition, depending on this XGXS function,
> > PHY-XS or DTE-XS,
> > > this bit is set by different modules in any of the cases.
> >
> > This was what I was trying to say above. However, these bits
> > are not set when upon detection of LF sequences, only when the
> > data path is not yet operational. When the data path is operational,
> > LF sequences are simply forwarded along without any mention to
> > management until they get to the RS where they are noted.
> >
> > >
> > > 4.The same is true  for bits 5.8.10 vs. 4.8.10
> > >
> > > It would be better to define:
> > >
> > > 5.8.11 as Tx path LF Detection for DTE-XS
> > > 4.8.11 as Rx path LF Detection for PHY-XS
> > > 5.8.10 as Rx path LF Detection for DTE-XS
> > > 4.8.10 as Tx  path LF Detection for PHY-XS
> > >
> > > BTW this method works in all other cases of symmetrical
> > functionality
> > > between PHY-XS and DTE-XS because it saves a MUX in the
> > implementation, and
> > > more consistent.
> >
> > This issue has been discussed before and the draft reflects
> > how it was settled. If you want to raise the issue again, you'll
> > have to submit a comment against the next draft.
> >
> > Regards,
> > Ben
> >
> > >
> > > CLAUSE 48 Question
> > > Section 48.2.5.4.1 defines local_fault as follows: "A local
> > fault condition
> > > is recognized by the PCS whenever align_status=fail". Combining this
> > > definition with those in clause 45 can lead to the
> > erroneous conclusion that
> > > the events "Link Status Fail" and "Local fault detection"
> > are identical. So
> > > I think it should be changed either in 45 or in 48 (Unless
> > this is really
> > > the intention).
> > >
> > > Best regards,
> > > Boaz
> >
> >
> > --
> > -----------------------------------------
> > Benjamin Brown
> > AMCC
> > 2 Commerce Park West
> > Suite 104
> > Bedford NH 03110
> > 603-641-9837 - Work
> > 603-491-0296 - Cell
> > 603-626-7455 - Fax
> > 603-798-4115 - Home Office
> > bbrown@xxxxxxxx
> > -----------------------------------------
                     
---------------------------------------------------------
Richard Taborek Sr.                     Intel Corporation
XAUI Sherpa                    Intel Communications Group
3101 Jay Street, Suite 110         Optical Products Group
Santa Clara, CA 95054           Santa Clara Design Center
408-496-3423                                     JAY1-101
Cell: 408-832-3957          mailto:rich.taborek@xxxxxxxxx
Fax: 408-486-9783                    http://www.intel.com