Thread Links Date Links
Thread Prev Thread Next Thread Index Date Prev Date Next Date Index

Re: Interface reality check




Rich,

I notice in your drawings, you do not have the frame stuffed PHY as proposed
originally for the WAN compatible PHY.  Does this mean that your proposals
here are for the LAN only PHY specifically and not other PHYs?

Thank you,
Roy Bynum

----- Original Message -----
From: Rich Taborek <rtaborek@earthlink.net>
To: HSSG <stds-802-3-hssg@ieee.org>; David Law <David_Law@3com.com>;
Benjamin J. Brown <bebrown@nortelnetworks.com>
Sent: Friday, March 31, 2000 6:55 PM
Subject: Re: Interface reality check


> Ben,
>
> Attached to this note is a PDF file containing a proposal to modify the
> Reconciliation Sublayer to enable the transport of data and control codes
in a
> PCS and XAUI independent manner. The proposal contains a reference 10 GbE
> implementation and multiple examples of code translation between two 10
GbE
> devices, Device A and Device B. It took too long to draw the figures in
ASCII
> and the end result was ugly, so I resorted to PowerPoint. The proposal can
be
> described in the following simple terms:
>
> - The XGXS transmitter translates Idle /I/ to XAUI Idle /A/K/R/;
> - The RS receiver translates /A/K/R/ to /I/;
> - The XGMII, XAUI/XGXS, PCS, PMA and medium transport all RS codes
> transparently.
>
> It is likely that the attached file is too large for this reflector, so
you may
> either not receive this note at all, or the file associated with it will
not get
> through. If this happens, I'd like to request Mr. David Law to post the
attached
> file to the "email_attach" directory at:
> http://grouper.ieee.org/groups/802/3/10G_study/public/email_attach/
>
> I'll monitor this reflector for the fate of this note and the attached
file.
>
> Additional comments below:
>
> Best Regards,
> Rich
>
> --
>
> Brown, Ben wrote:
> >
> > Rich,
> >
> > See comments below:
> >
> > Rich Taborek wrote:
> > >
> > > The issue is not whether XAUI encodings are required for 64B/66B, the
issue is
> > > whether either the MAC needs to signal the PHY with anything other
than Idles or
> > > the PHY itself needs to signal over the medium.
> >
> > Agreed.
> >
> > > I completely forgot about the obvious case of ERROR, where the MAC
transmitter
> > > or the PHY at any point in the link needs to replace a data or control
code with
> > > an ERROR code. In order to support this proposed function, 64B/66B
must
> > > transport /E/ codes in addition to /I/ codes across the medium.
> >
> > Of course, and don't forget /S/, /T/ and /D/.
> >
> > > Note that Gigabit Ethernet also signals Break Link and Remote Fault
through the
> > > use of Config words, which are essentially a control encoding
different than the
> > > GbE idle stream. Several folks including Mr. Howard Frazier and myself
have
> > > already alluded to the benefit and compatibility of supporting Break
Link and
> > > Remote Fault for 10 GbE.
> >
> > This is a good example of codes in addition to those required by the
> > MAC/RS. So this means there is precedent to send information across the
> > link other than that information which comes from/to the MAC via the RS.
> > However, these codes are only used as a startup (Auto-Neg) or to
> > signal error conditions (remote fault & break link). They are not
> > present between every packet.
>
> I agree to the first part of the paragraph above. However, the
architecture and
> implementation for the MAC and PHY to initiate, transport and receive
control
> information other than Idle and Packets is intimately intertwined with
Idle and
> Packet information. In fact, Ethernet can be considered to be an Idle
stream
> transport which is rudely interrupted to transport Packets, Initialize the
link,
> or report Errors.
>
> I'm not sure I understand either the relevance or accuracy of your
statement
> that: "They (codes) are not present between every packet." Control
information
> may indeed be required between every packet (e.g. Rate Control, Error,
etc.) The
> fact that control information transport may be required between ANY packet
is
> relevant.
>
> > > This makes for a potential requirement to signal at least three
control codes
> > > besides /I/, /T/, /S/ and /D/ across 64B/66B and the medium. A further
> > > requirement is to support the transport of these codes through the
optional
> > > instantiations of the PCS Service interface.
> >
> > I agree that these codes may need additional encoding to go across
> > something such as XAUI. I don't agree that this additional coding
> > cannot be removed at the end of the XAUI.
>
> Major disconnect. The "three control codes" mentioned above are: Break
Link,
> Remote Fault and Error. These codes cannot be removed at the end of XAUI
(I
> assume that you mean by the XGXS) since the codes are destined for either
the
> PCS or the RS. In the case that the destination is the PCS, the PCS is
> responsible for transporting these codes over the medium to the remote
link end.
> In the case that the destination is the RS, the XGXS is responsible for
> transporting these codes over the XGMII, if present, or directly
delivering the
> codes to the RS. It should be clear that these codes cannot be removed by
> XAUI/XGXS unless a trap for a specific code is specified. Am I completely
> misinterpreting your response?
>
> > > One way I'll propose to do this cleanly is to have the RS receiver
treat /A/K/R/
> > > the same as /I/. In fact, all codes other than /T/, /S/, /D/ and /E/
could be
> > > treated as /I/ by the RS receiver until those other codes are defined
by 10 GbE.
> > >
> > > No translations by the PCS, including 64B/66B, would be necessary.
> >
> > It's not a matter of this translation being necessary. I keep getting
> > the feeling that you're trying to make the PCS "easier" by "keeping"
> > the /A/K/R/ rather than converting them back to /I/. If all
> > implementations used XAUI than this could indeed be considered
> > "easier". However, if we're not going to force the use of XAUI then
> > "keeping" /A/K/R/ is not necessarily "easier". Am I reading you
> > incorrectly? (The above quotes are for emphasis. They are not meant
> > to imply that you've used these words.)
>
> I believe that we both made very good points in this thread about the
> practicality and impracticality of performing code conversion required to
> support optional interfaces. You are reading me to a "tee" by saying that
I am
> trying to make the PCS easier. I am trying to make the entire PHY as
simple as
> possible by considering the requirements and flexibility of all elements.
I
> think you'll find the attached proposal to your liking :-)
>
> > > Whaddya think?
> >
> > I'll reserve judgement until I see the full proposal.
> >
> > Ben
> >
> > --
> > -----------------------------------------
> > Benjamin Brown
> > Router Products Division
> > Nortel Networks
> > 1 Bedford Farms,
> > Kilton Road
> > Bedford, NH 03110
> > 603-629-3027 - Work
> > 603-624-4382 - Fax
> > 603-798-4115 - Home
> > bebrown@nortelnetworks.com
> > -----------------------------------------
>
> -------------------------------------------------------
> Richard Taborek Sr.                 Phone: 408-845-6102
> Chief Technology Officer             Cell: 408-832-3957
> nSerial Corporation                   Fax: 408-845-6114
> 2500-5 Augustine Dr.        mailto:rtaborek@nSerial.com
> Santa Clara, CA 95054            http://www.nSerial.com