RE: 10GE data rate?
- To: "'Rich Taborek'" <rtaborek@xxxxxxxxxxxxxxxx>, "'nuss@xxxxxxxxxx'" <nuss@xxxxxxxxxx>, "'HSSG'" <stds-802-3-hssg@xxxxxxxx>, "'HSSG Speed'" <stds-802-3-hssg-speed@xxxxxxxx>
- Subject: RE: 10GE data rate?
- From: Drew Perkins <drew.perkins@xxxxxxxxxxxx>
- Date: Thu, 24 Jun 1999 23:40:12 -0700
- Sender: owner-stds-802-3-hssg-speed@xxxxxxxxxxxxxxxxxx
As already said, at the end of the day #1 and #2 are the same. The
only difference might be internal implementation difference (chip
interfaces). The resulting protocol on the wire may be precisely the same,
or may differ only by inclusion of preambles, IFGs, etc. vs. POS encodings.
Why do you say that #2 is a step in the wrong direction?
Ciena Corporation Email: ddp@xxxxxxxxxxxx
Core Switching Division Tel: 408-865-6202
10201 Bubb Road Fax: 408-865-6291
Cupertino, CA 95014 Cell/Pager: 408-829-8298
[mailto:owner-stds-802-3-hssg@xxxxxxxxxxxxxxxxxx]On Behalf Of Rich
Sent: Wednesday, June 23, 1999 1:18 AM
To: nuss@xxxxxxxxxx; HSSG; HSSG Speed
Subject: Re: 10GE data rate?
In an early note to the HSSG Speed reflector, I summarized my view of all
schemes discussed thus far to support the WAN at Ethernet rates of ~10 Gbps.
I'll repost that summary here to make it available to the larger HSSG
reflector. The three schemes I have come up with are:
1) Legacy: 10Gbps Ethernet switched/bridged/routed to Sonet. We simply need
to specify a 10 Gbps PHY to make this fly.
2) SONET-based PHY: A new Ethernet PHY compatible with OC-192 SONET that
connects directly to the Ethernet MAC, which runs at SONET OC-192 rates.
This is the new PHY suggested by Paul. Looking forward, the next higher
Ethernet speed variant would likely be OC-768.
3) 10 Gbps Ethernet WAN PHY: A new Ethernet PHY supporting WAN dark fiber
and/or DWDM equipment, sans SONET. I believe that this is one of the options
proposed by Bill St. Arnaud among others.
My scheme (3) seems to correspond with Martin's (1) and (3) below and is a
PHY variant which supports a data rate of exactly 10.0 Gbps. Other qualities
of this PHY may include any or all of the following:
a) Direct drive of long-haul dark fiber and/or DWDM equipment;
b) Simplex and/or duplex channels;
c) Standard Ethernet facilities for out-of-band signaling and cable plant
management including MAC Control frames, Auto-Negotiation, and (I hate to
even suggest it) Primitive Signaling using alternate "Idle" codes. Ethernet
out-of-band signaling capabilities are actually more extensive than most
protocols I'm aware of.
(1) above seems supports the existing SONET infrastructure quite adequeately
and allows high performance switch/bridge/router products to be implemeted
in a manner of highest compatibility with the LAN and WAN.
(2) sabove ignificantly affects the existing LAN market through its dictate
of SONET speeds and other peculiarities not applicable to existing LANs and
is a step in the wrong direction .
(3) above takes Ethernet where no Ethernet has gone before and treads
directly on the existing WAN infrastructure. This latter alternative will be
difficult to go forward with also since the "LAN" folks consider it to be
outside the scope of 802, and the "WAN" folks view it as a significant
territorial encroachment. However, once (1) happens, the cost advantages of
it will inevitably drive implementations and products based on (3).
Martin Nuss wrote:
> I wanted to get your expert opinion on a few issues that would be of
> interest to me as we go forward in the standard:
> 1) do you really believe that we need to support all the WAN OAMP
> features in 10GE? I would rather prefer a light-weight 10ge protocol
> that guarantees the lowest cost in the LAN, but make sure that it can be
> wrapped easily into a WAN envelope to support all the WAN features.
> 2) at the last meeting, Paul Bottorff as well as Mike Salzman presented
> approaches to a serial 10GE standard based on scrambling as opposed to
> block coding. Both of these could be used for a low-cost serial LAN
> standard, and wrapped into WAN envelopes like SONET to provide WAN OAMP
> features. The 10GE data rate would have to be kept to around 9.6 Gb/s
> to make that possible at the lowest cost. Presumably, that would
> accelerate the acceptance of 10GE in the WAN.
> 3) Alternatively, we could propose to allow for additional control
> fields in the 10GE standard that duplicate the functions most important
> for WAN apps. This may be the cleanest solution, but it will require
> 802.3 to venture into an area that it has not worried about before...
> Any thoughts?
Richard Taborek Sr. Tel: 650 210 8800 x101 or 408 370 9233
Principal Architect Fax: 650 940 1898 or 408 374 3645
Transcendata, Inc. Email: rtaborek@xxxxxxxxxxxxxxxx
1029 Corporation Way http://www.transcendata.com
Palo Alto, CA 94303-4305 Alt email: rtaborek@xxxxxxxxxxxxx