Thread Links Date Links
Thread Prev Thread Next Thread Index Date Prev Date Next Date Index

Re: [BP] Simulations for EIT



prakash,

Although the EIT simulations are being done to determine suitable test 
conditions for the receiver, it is not a test of the Rx. In the 
simulations the receiver's function is to compare the amount of stress 
it is getting from the test interference signal in the simulated Rx test 
to the stress it will see in operation with worst case channels. The 
comparison should be valid regardless of any details of the receiver 
(including but not limited to whether it is worst case) as long as neither:

1. We have not so worst cased the Rx that its errors rate is essentially
saturated and we no longer have any resolution on stress.
2. The simulated receiver's relative sensitivity to test interference
and real interference are representative of real receivers. This
will be more likely as we make the test interference more like
real interference. This is an argument for using broad band
interference in the test.

charles

Radhakrishnan, Prakash K wrote:

> Pat
>
> If you are talking about worst case why not consider all the PVT 
> variations of the Silicon too ? For instance why is the latch 
> threshold set to 10mv ?
>
> ------------------------------------------------------------------------
>
> *From:* Pat Thaler [mailto:pthaler@BROADCOM.COM]
> *Sent:* Friday, March 17, 2006 10:03 AM
> *To:* STDS-802-3-BLADE@listserv.ieee.org
> *Subject:* Re: [BP] Simulations for EIT
>
> Rich,
>
> One can't assume that implementations are done such that the limits in 
> the spec are at the 3 sigma points with the mean about the middle. 
> Implementations won't necessarily be built to the average of the spec. 
> For instance, I've seen cases with past standards of interoperability 
> problems where one vendor chose to put their transmit level close to 
> the minimum with tight standard deviation (trying to optimize for 
> emmissions, power consumption, etc.) and another vendor put their 
> input sensitivity near the maximum. Another example is that sometimes 
> one or more of the specs is particularly difficult to achieve and 
> designs have an average value that is very close to the limit. A 
> vendor may even take a yield hit and sort out those chips that are 
> over the limit so occurance at or near the limit value happens much 
> more often than 3 sigma would predict.
>
> In the past standards I've worked on, we have usually assumed that 
> implementations could be running at the limits because we don't have a 
> basis for assuming a distribution. Where we have applied distribution, 
> it has been to channel characteristics for which we had some basis for 
> believing there would be a distribution - e.g. not all channels will 
> have the worst crosstalk situation.
>
> Also, a typical backplane system will have a lot of links. If 90% of 
> them work, the system still has a problem. We have to do a good deal 
> better than that.
>
> Pat
>
> ------------------------------------------------------------------------
>
> *From:* Mellitz, Richard [mailto:richard.mellitz@INTEL.COM]
> *Sent:* Thursday, March 16, 2006 4:20 PM
> *To:* STDS-802-3-BLADE@listserv.ieee.org
> *Subject:* Re: [BP] Simulations for EIT
>
> Ya know… I just did a statistical analysis of the probability of units 
> failing the return we just voted on. Under some assumptions I made, I 
> came up with 2.5 units per 1000 would fail RL and still pass. I heard 
> folks thought this might be something like 90%. The design question is 
> what quality level is acceptable. I understand this from a business 
> perceptive because I can relate it to cost. I don’t know how to apply 
> this to standard work. Maybe it does mean all limits at the worst case 
> must work regardless of the likelihood. Maybe this is a Pandora’s Box 
> too. I think our cost is not dollars but delay producing a workable 
> standard.
>
> The 80% Joel was talking about was design engineers. This is not the 
> statistics of a design’s quality. If I +/-3 sigma all our limits in 
> the spec, I think we are more like in the 99.9+% quality range right now.
>
> The task at hand was to determine if the informative channel spec 
> sufficiently predicted confidence related to the EIT receiver test. 
> That why we used the term “confidence” and not “limit.” Remember that 
> is why we chose the channel to be informative. We showed we couldn’t 
> constrain all 3 (tx, channel, rx) and create a reasonable and 
> marketable solution. So in light of that I believe we should constrain 
> the analysis to reasonable. Maybe we should do it both ways and 
> discuss what is reasonable at April 19 meeting.
>
> … Rich
>
> ------------------------------------------------------------------------